Description

Pneumatic Training System

Technical Specification :

Pneumatic training device is at the request of modern
pneumatic professional teaching experiment, according to the hydraulic and pneumatic transmission ”, ”the
Pneumatic control technology”, etc., general teaching
material contents design.
The system in Addition
Meet the base and teaching training system of need of
practical applications
Equipment structure is firm and has good stability
Low noise operation
layout clear and intriguing design
The four truckle with crack slot in order to move and
install on the work table. Panel grooves intervals are 25
mm, can easily move all kinds of components insert on
it.
Various pneumatic components into separate module
which is equipped with bottom panel of elastic pins,
when training they can build all kinds of pneumatic
circuits on general aluminum, fast loading and
unloading, flexible layout, clear pneumatic circuit
Electrical control units used for independent relay
control unit and multi-button unit control electrical,
simple and clear!
High safety: have over-current protection, the power
supply will cut off as earth leakage exceed 30mA; the
electrical control use DC 24v power supply, with over
current protection, can prevent damage to the
equipment caused by improper operation. system
nominal pressure is 0.6MPa.

Pneumatic basic control circuit experiment:
Single acting cylinder automatic control,
Double acting cylinder automatic control,
PLC control technical application
Relay control technical application
Other comprehensiveness, expansibility experiment
type pneumatic circuit.

Pneumatic basic experiment circuits illustrate:
Single acting cylinder reversing circuit,
Double acting cylinder reversing circuit,
Single acting cylinder speed control circuit,
Double acting cylinder one-way speed regulation
circuit,
Double acting cylinder both-way speed regulation
circuit,
Speed changing-over circuit,
Buffering circuit,
Twice pressure control circuit,
High and low voltage convert circuit,
Delay circuit,
Overload protection circuit,
Interlocking circuit,
Single cylinder single reciprocating control circuit,
Single cylinder continuous reciprocating action circuit,
Multi cylinder sequence action circuit
Double-cylinder synchronization action circuit,
Unloading circuit,
Or gate type valve shuttle application circuits,
And gate application circuit of double press valve,
Rapid exhaust valve application circuit,
Magnetic induction type proximity switch application;
Sensor application in control system
Relay control circuit

Specification : 
DC power: input, AC220V, 50Hz/60 Hz Output: DC
24V/3A
Air compressor (basic equipment minimal machine):
power: AC 220V±10% 50Hz/60Hz motor power: 600W
Nominal volume: 9L normal output pressure voltage
0.7 MPa, noise degree: 66 dB
Groove interval: 25mm
Table top structure: 1
With crack slot truckle: 4
Relay module:
coil voltage: DC 24V;
contactor type: circuit common-NO-NC
Contact capacity: AC 240V/10A/DC24V/10A
Button module: Signal lamp power supply: DC 24V
Contact capacity: AC220V/1A DC24V/2A
Mechanical electrical life: 1 million times (Min)
Workbench experiment table Dimension
(Minimum)1360 (length)×650 (width)×1650
(height Aluminum panel dimension:1200×600
Manifold Block Working pressure: 0.5MPa Max
pressure:0.8MPa input: φ6 output:φ4; one-way
Double-acting Cylinder diameter:20mmstroke:
100mmworking pressure range:0.1~1MPaa
Single-acting cylinder: diameter:20mm
stroke:100mm
working pressure
range:0.1~1MPa
5/3 solenoid directional valve central vented: DC
power:DC24V Working pressure
range:0.15~0.8MPa
Drive way: electric control
5/2 single solenoid shuttle valve: voltage:DC24V
Working pressure range: 0.15~0.8MPa
Drive way: electric control
5/2 double solenoid shuttle valve: 02 Nos
3/2 single solenoid shuttle valve NC:01 Nos
3/2 single solenoid shuttle valve NO: 01 Nos
5/2 handle shuttle valve Mushroom button valves:01
No
5/2 handle shuttle valve: 01 No
5/3 handle shuttle valve: 01 No
Single pneumatic control 3/2: 01 No
Double pneumatic control 3/2: 01 No
Double pneumatic control 5/2: 02 Nos
Dyad:01 No
(Pressure regulator:0.15~0.9MPa)
Reducing valve: 02 nos
One-way valve: 02 nos
Pressure gauge:02 nos
One-way throttle valve:02 nos
3/2 knob valve:01 no
3/2 Stroke valve:02 nos
Time delay valve:02 nos
Sequence valve:01 no
And gate-type dual pressure:02 nos
Or gate-type shuttle valve:02 nos
Quick escape valve:01 no
Micro switch valve (left trigger) :02 nos
Photoelectric Sensor:01 no
DC power supply unit: 01 No
HoseФ4:100ft
4 T Valve:03 Nos
Three connections:03 Nos
APG reducing straight coupling:03 Nos

Accessories : 
Air Compressor-01 no
Connecting jack 2mm & 4mm: 01 Set
Power Cable: 01 no
PLC to PC Communication cable: 01 Sets
Simulation softw are for compatible PLC
English Manual & CD: 01 Set
Standard accessories.

Others :
Origin: China, Taiwan, Japan.
Manufacturing in Bangladesh.
Warranty: 01 year.
Installation, Testing.
Training.