Electrical Machine Training System with Simulation Software

Description

Electrical Machine Training System with Simulation Software

Technical Specification :

Experimental Modules: Field resistor module
It connected to the field winding of the DC motor and used as a
regulating resistor. The generator can control the generated voltage,
and the motor should control the speed.
Variable resistance: 100W, 100Ω
Connection terminal (4mm insulated type)
Direct/AC load module :Used as a single‐phase load in series / AC.
The load should use lamps and bulbs of 3V, 6.3V, 12V depending on the capacity of the voltage.
Lamp socket (6.3T socket)
Lamp used: 3V, 6.3V, 12V
Connection terminal black, red, yellow (4mm insulated type)
3‐phase load module
Three‐phase loads should be available in two types, Y and Δ.
Lamp socket (6.3T socket)
Lamp used: 3V, 6.3V, 12V
Connection terminal black, yellow (4mm insulated type)
o R, L, C load module
Modules should be designed for use with R, L and C loads.
Toggle switch
Resistance (20W 10Ω, 20W 30Ω, 20W 50Ω)
Coil (0.2H, 0.4H, 0.8H)
Capacitor (220V 8.5uF)
Connection terminal black (4mm insulated type)
Power supply module
This voltage can be used to supply DC power via a bridge diode.
By using tap on the secondary side of transformer, various
AC voltages such as 6.3V, 12V, 24V, 50V can be obtained.
Various DC voltages for:
AC Voltmeter (0 ~ 80V)
DC voltmeter (0 ~ 80V)
Power switch: 1ea
Connection terminal black, red (4mm insulated type)
AC voltage / ammeter module
AC voltage can be measured in units of 5V, 10V, 50V,
AC current can be measured in units of 0.1 A, 1 A, 2.5 A, 5 A.
AC voltmeter (5V, 10V, 50V)
AC ammeter (0.1 A, 1 A, 2.5 A, 5 A)
DC voltage / ammeter module
DC voltage can be measured in units of 5V, 10V and 50V.
DC current can be measured in units of 0.1 A, 1 A, 2.5 A, 5 A
DC voltmeter (5V, 10V, 50V)
DC ammeter (0.1A, 1A, 2.5A, 5A)
DC galvanometer module
Measures from ?5mA to + 5mA.
It is possible to measure from 500mA to + 500mA by changing the
range.
DC galvanometer (‐5mA ~ + 5mV / ‐500mA ~ + 500mA)
Rotary switch (3 steps)
Yoke frame module
Used to make the basic structure of generators and electric motors.
Produce generators and motors of various structures such as direct
current generators, single and three‐phase alternators, direct current
motors, direct current lottery motors, squirrel cage induction motors,
rebound motors, phase motors, and shading coil motors.
Yoke frame (Φ190 x 18)
Board stand (Φ12 x 68)
Connection terminal black (4mm insulated type)
Drive motor module
In the generator experiment, a device that should rotate the rotorto
generate power in place of energy sources of various generators.
The belt should be engaged with the motor pulley and the rotor
of the generator to generate power.
The direction of rotation can be changed by the operation of the cam
switch, and the amount of power generated by controlling the rotation speed of the motor using the speed controller.
Power switch
Cam switch (three steps of two)
Motor Pulley (Φ20 x Φ30 x 85)
Motor (Single Phase 220V 6W)
Speed controller (analog type)
RPM meter
Polar Number Switcher Module
When operating with Y and Δ, change the Y / Δ with cam switch.
Cam switch (three steps of five)
Experimental Boards:
3-Phase Machine, DC Machine, Rotary Converter, Compound Wound Motor, Induction Motor-Speed Control, Repulsion Motor,-
Split-Phase Motor.
3) Assembling Machine Parts:
Disk Slot Rotor Coil: 1ea
2-Pole,3-Pole Rotor, Wound Rotor, Squirrel-Cage Rotor, Disk
Slot Rotor’s Short Ring: 1ea(each)
Compass: 1ea
Round-Type Permanent Magnet: 2ea
Wide Magnetic Pole for Permanent Magnet: 2ea
Wide Magnetic Pole for Field Coil: 5ea
Narrow Magnetic Pole for Field Coil: 6ea
Polarized Magnetic Pole for Field Coil: 2ea
Field coil (300-turn): 6ea
Field coil (700-turn): 2ea
Field coil (1700-turn): 2ea
Brush & Holder Set: 3sets
Rotor fixture: 2ea
Magnetic Pole fixture: 10ea
Bolt: 10ea
Spanner: 1ea
Driving Belt: 1ea
3V,5V,6.3V,12V Load Lamp: 5ea
Bar Type Permanent Magnet : 1ea

Accessories :
User manual.
Connecting Wire
Single Phase power cord.

Others :
Installation, Testing, and Training.
Warranty: 01(One) Year
Origin: China. taiwan, Japan,
Manufacturing: Assemble in Bangladesh.